Technologies and XXII
להגדלת הטקסט להקטנת הטקסט- ספר
Collection of selected, peer reviewed papers from the XXII Conference on Technologies and Properties of Modern Utility Materials, (TPMUM 2014), May 16, 2014, Katowice, Poland. The 42 papers are grouped as follows: I: Materials Analysis; II: Processing Technologies; III: Surface Engineering; IV: Materials and Environment Collection of selected, peer reviewed papers from the XXII Conference on Technologies and Properties of Modern Utility Materials, (TPMUM 2014), May 16, 2014, Katowice, Poland. The 42 papers are grouped as follows: I: Materials Analysis; II: Processing Technologies; III: Surface
כותר |
Technologies and XXII : Selected, peer reviewed papers from the XXII Conference on Technologies and Properties of Modern Utility Materials, (TPMUM 2014), May 16, 2014, Katowice, Poland / edited by Jacek Mendala Paweł Grado. |
---|---|
מהדורה |
1st ed. |
מוציא לאור |
Plaffikon, Switzerland : Trans Tech Publications |
שנה |
2015 |
הערות |
Description based upon print version of record. Includes bibliographical references and index. English |
הערת תוכן ותקציר |
Technologies and Properties of Modern Utility Materials XXII Preface Table of Contents I. Materials Analysis Microstructure and Properties of Ti-47Al-2W-0.5Si Cast Alloy Determination of Nickel in Welding Fume by Gravimetric Method Using Dimethylglyoxime Estimation of Carbon Balance in Reaction Zones of a Submerged-Arc Furnace during Ferrosilicon Smelting The Origin of the Ferroelectricity in the Bismuth Titanate Bi4Ti3O12 with Perovskite-Like Layered Structure Thermal Stability of Ti-6Al-4V Alloy with Carbon Content Biomechanical Analysis of Selected Endoprostheses of Hip Joint by Means of Finite Element MethodsEffect of Heat Treatment on the Microstructure and Mechanical Properties of Sintered Stainless Tool Steel The Influence of Addition of the Rare Earth Elements on the Structure and Hardness of AlZn12Mg3.5Cu2.5 Alloy Effect of Autogenous Laser Weld on Microstructure and Mechanical Properties of Inconel 617 Nickel Alloy II. Processing Technologies Strength-Energy and Structural Effects of Dynamic Deformation of Aluminum Alloy Influence of the Materials Combination for the Surface Temperature of the Bimetallic Wire Deformed in the Cold Drawing ProcessPreparation of SiCw-ZTA Composites by Two-Step Sintering or Spark Plasma Sintering Tests of Welded Joints of New Generation Austenitic, Stainless Steel HR3C Fatigue Behaviour of Carbide Precipitation Hardened Austenitic Steels Influence of the Thermo-Mechanical Treatment on the Properties and Microstructure of High Manganese Austenitic-Ferritic Steel Durability of Tube Bends Made of the 14MoV6-3 Steel under Low-Cycle Fatigue Conditions and Creep at a Temperature of 500°CCracking of 7CrMoVTiB10-10 (T24) Steel Weld Joints The Influence of the Solutionizing and Ageing on the Structure and Hardness of the ZnAl40Cu3 Alloy Evaluation of Susceptibility to Hot Cracking of Inconel 617 Nickel Alloy Welds in Transvarestraint Test Microstructure and Mechanical Properties of High Manganese TWIP Steel after Thermo-Forming Processes The Causes of Low Impact Strength of T23 Steel Weld Joints Welding Duplex Steel Type X2CrNiMoN25-7-4 with Analysis of Ferrite Content Measurements in Welded JointsUsefulness of Quartzites for the Production of Ferrosilicon Porosity of Solid and Cored Turbine Blades of Aircraft Engines III. Surface Engineering Laser Remelting of Silicide Coatings on Mo and TZM Alloy Profilometric Assessment of Surface Condition of Zinc Coatings Formed by the Continuous Galvanizing Method The Influence of Si Content in Steel on Growth Kinetics and Structure of Hot Dip ZnAl23Si Coatings High Temperature Cyclic Oxidation of Coatings on Ni-Based Superalloys Zinc Coatings Obtained by Hot Dip Method on the High Strength Steel for Link Chains |
סדרה |
Solid State Phenomena v.226 |
היקף החומר |
1 online resource (227 p.) |
שפה |
אנגלית |
שנת זכויות יוצרים |
©2015 |
מספר מערכת |
997010716523805171 |
תצוגת MARC
יודעים עוד על הפריט? זיהיתם טעות?